OpenVoiceOS

History

j1nx a68ff2c35e [ALL] RealTime kernel/system changes. - Raspberry Pi: Using the RT patches and select RT as PREEMPT - Pipewire changes to upvote itself to prio 95% nice -19 - Other small kernel tweaks and fixes		2024-01-04 12:38:55 +00:00
..
patches/kernel	[All][RPI] Clean ups and some fixed (+kerenl bump)	2023-12-17 13:49:45 +00:00
rootfs-overlay	[RPI] Fix Mark1 i2csound detection	2023-12-29 16:07:36 +00:00
rpi3	[ALL] First try-out on pre loading the podman containers at buildtime	2023-11-30 18:24:34 +00:00
rpi4	[RPI4] Bump gpu memory to 256 as 128 might not be enough.	2023-12-03 11:50:38 +00:00
cmdline.txt	[ALL] Bump buildroot + podman/crun [RPI] Update configs for it.	2023-10-28 14:31:43 +00:00
grub-efi.cfg	[ALL] Small fixes to the update mechnism	2023-09-14 06:29:39 +00:00
kernel.config	[ALL] RealTime kernel/system changes.	2024-01-04 12:38:55 +00:00
post-build.sh	[ALL] Fixes (non-boot rpi) and tweaks (pipewire/wireplumber)	2023-12-27 16:11:15 +00:00
post-image.sh	More work and get rpi4 inline	2023-08-21 08:05:43 +00:00
readme.txt	Splitting the build system for base and gui images	2023-04-08 14:42:52 +02:00

readme.txt

Raspberry Pi

Intro
=====

These instructions apply to all models of the Raspberry Pi:
  - the original models A and B,
  - the "enhanced" models A+ and B+,
  - the model B2 (aka Raspberry Pi 2)
  - the model B3 (aka Raspberry Pi 3).
  - the model B4 (aka Raspberry Pi 4).

How to build it
===============

Configure Buildroot
-------------------

There are two RaspberryPi defconfig files in Buildroot, one for each
major variant, which you should base your work on:

For models A, B, A+ or B+:

  $ make raspberrypi_defconfig

For model Zero (model A+ in smaller form factor):

  $ make raspberrypi0_defconfig

For model 2 B:

  $ make raspberrypi2_defconfig

For model 3 B and B+:

  $ make raspberrypi3_defconfig

For model 4 B:

  $ make raspberrypi4_defconfig

Build the rootfs
----------------

Note: you will need to have access to the network, since Buildroot will
download the packages' sources.

You may now build your rootfs with:

  $ make

(This may take a while, consider getting yourself a coffee ;-) )

Result of the build
-------------------

After building, you should obtain this tree:

    output/images/
    +-- bcm2708-rpi-b.dtb           [1]
    +-- bcm2708-rpi-b-plus.dtb      [1]
    +-- bcm2709-rpi-2-b.dtb         [1]
    +-- bcm2710-rpi-3-b.dtb         [1]
    +-- bcm2710-rpi-3-b-plus.dtb    [1]
    +-- bcm2711-rpi-4-b.dtb         [1]
    +-- boot.vfat
    +-- rootfs.ext4
    +-- rpi-firmware/
    |   +-- bootcode.bin
    |   +-- cmdline.txt
    |   +-- config.txt
    |   +-- fixup.dat
    |   +-- start.elf
    |   `-- overlays/               [2]
    +-- sdcard.img
    `-- zImage

[1] Not all of them will be present, depending on the RaspberryPi
    model you are using.

[2] Only for the Raspberry Pi 3/4 Models (overlay pi3-miniuart-bt is needed
    to enable the RPi3 serial console otherwise occupied by the bluetooth
    chip). Alternative would be to disable the serial console in cmdline.txt
    and /etc/inittab.

How to write the SD card
========================

Once the build process is finished you will have an image called "sdcard.img"
in the output/images/ directory.

Copy the bootable "sdcard.img" onto an SD card with "dd":

  $ sudo dd if=output/images/sdcard.img of=/dev/sdX

Insert the SDcard into your Raspberry Pi, and power it up. Your new system
should come up now and start two consoles: one on the serial port on
the P1 header, one on the HDMI output where you can login using a USB
keyboard.