OpenVoiceOS/buildroot-external/rootfs-overlay/usr/bin/tas5806-init

#!/usr/bin/env python
##########################################################################
# tas5806-init
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#    http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
##########################################################################
'''
install:
    pip3 install smbus2

run:
    python3 tas5806Test.py
'''
from smbus2 import SMBus
# Open i2c bus 1 and read one byte from address 80, offset 0

import os
import time
import subprocess

class tasTest:
    devAddr = 0x2f
    bus = ""

    commandReturn = ""
    
    def __init__(self):
        self.bus = SMBus(1)
        
    def dumpData(self):
        #for i in range(0x10):
        #    b = self.bus.read_byte_data(self.devAddr, i)
        #    print("%s: %s" % (hex(i), hex(b)) ) 
            
        #print("------------------")
        commandSend = 'i2cdump -y 1 ' +str( self.devAddr) +' W'
        #os.system(commandSend)
        self.commandReturn = os.popen(commandSend).read()
        #print(self.commandReturn)
        self.checkErrors()
        
    '''
        Check through error codes in i2cDump
    '''
    def checkErrors(self):

        # register 0x37
        fsMon = self.commandReturn.splitlines()[4][25:27] 
        fsMonBin = "{0:08b}".format(int(fsMon, 16))
        fsMonStr = ["FS Error","","","","","","32KHz","","Reserved","48KHz","","96KHz"]
        #print("FS_MON: %s (0x37)" % (fsMon))
        print("FS_MON: %s   (reg: 0x37)" % fsMonStr[int(fsMon)] )
        
        
        # (reg: 0x70)
        errorString = self.commandReturn.splitlines()[8][4:6] 
        errorStringBin = "{0:08b}".format(int(errorString, 16))
        if(errorStringBin[-4] == "1" ):
            print("Left channel DC fault" )
        if(errorStringBin[-3] == "1" ):
            print("Right channel DC fault" )
        if(errorStringBin[-2] == "1" ):
            print("Left channel over current fault" )
        if(errorStringBin[-1] == "1" ):
            print("Right channel over current fault" )

        # (reg: 0x71)
        errorString = self.commandReturn.splitlines()[8][7:9] 
        errorStringBin = "{0:08b}".format(int(errorString, 16))
        if(errorStringBin[-3] == "1" ):
            print("Clock fault (reg: 0x71)" )
            
        
        # register 0x68
        runStatus = self.commandReturn.splitlines()[7][29:31] 
        runStatusBin = "{0:08b}".format(int(runStatus, 16))
        #print(runStatus)
        runStatusStr = ["Deep sleep","Sleep","HIZ","Play"]
        print("Run Status: %s   (reg: 0x68)" % runStatusStr[int(runStatus)] )
        
    def writeData(self, addr, val, comment = "" ):
        self.bus.write_byte_data(self.devAddr, addr , val)
        #print("write: %s: %s - %s" %(hex(addr),hex(val), comment ) )
        time.sleep(0.1)
    
    def close(self):
        self.bus.close()
    
    '''
        Start Sequence for the TAS5806
    '''
    def startSequence(self):
        self.writeData(0x01,0x11, "Reset Chip") #reset chip
        self.writeData(0x78,0x80, "Clear Faults") #clear fault - works
        self.dumpData()
        self.writeData(0x01,0x00 , "Remove Reset") #remove reset
        self.writeData(0x78,0x00 , "Remove Clear Fault") #remove clear fault
        self.dumpData()

        #self.writeData(51,3) # 0x33 h set bit rate
        #self.writeData(118,64) # 0x76
        ##self.writeData(0x6A,3 , "")
        ##self.dumpData()

        #self.writeData(0x33,0x00, "16-bit") 
        #self.writeData(0x33,0x01, "20-bit") 
        #self.writeData(0x33,0x02, "24-bit") 
        self.writeData(0x33,0x03, "32-bit") 
        self.dumpData()
        self.setVolume(0x60) 
        self.writeData(0x30,0x01, "SDOUT is the DSP input (pre-processing)")


        self.writeData(0x03,0x00, "Deep Sleep") #Deep Sleep
        self.dumpData()
        #self.writeData(0x03,0x01) #Sleep
        #self.dumpData()


        self.writeData(0x03,0x02, "HiZ") #HiZ
        self.dumpData()

        self.writeData(0x5C,0x01, "coefficient") #Indicate the first coefficient of a BQ is starting to write
        self.dumpData()
        self.writeData(0x03,0x03 , "Play") #Play
        self.dumpData()

    def setVolume(self, vol):
        setVolStr = "Set Volume %s" %( str (vol) )
        self.writeData(0x4c,vol ,setVolStr) #Set volume

if __name__ == '__main__':
    tt = tasTest()
    tt.startSequence()
    tt.setVolume(50)
    tt.close()