mirror of
https://github.com/OpenVoiceOS/OpenVoiceOS
synced 2024-12-14 01:44:27 +01:00
94 lines
2.3 KiB
Plaintext
94 lines
2.3 KiB
Plaintext
|
Raspberry Pi
|
||
|
|
|
||
|
|
Intro
|
||
|
|
=====
|
||
|
|
|
||
|
|
These instructions apply to all models of the Raspberry Pi:
|
||
|
|
- the original models A and B,
|
||
|
|
- the "enhanced" models A+ and B+,
|
||
|
|
- the model B2 (aka Raspberry Pi 2)
|
||
|
|
- the model B3 (aka Raspberry Pi 3).
|
||
|
|
|
||
|
|
How to build it
|
||
|
|
===============
|
||
|
|
|
||
|
|
Configure Buildroot
|
||
|
|
-------------------
|
||
|
|
|
||
|
|
There are two RaspberryPi defconfig files in Buildroot, one for each
|
||
|
|
major variant, which you should base your work on:
|
||
|
|
|
||
|
|
For models A, B, A+ or B+:
|
||
|
|
|
||
|
|
$ make raspberrypi_defconfig
|
||
|
|
|
||
|
|
For model Zero (model A+ in smaller form factor):
|
||
|
|
|
||
|
|
$ make raspberrypi0_defconfig
|
||
|
|
|
||
|
|
For model 2 B:
|
||
|
|
|
||
|
|
$ make raspberrypi2_defconfig
|
||
|
|
|
||
|
|
For model 3 B and B+:
|
||
|
|
|
||
|
|
$ make raspberrypi3_defconfig
|
||
|
|
|
||
|
|
Build the rootfs
|
||
|
|
----------------
|
||
|
|
|
||
|
|
Note: you will need to have access to the network, since Buildroot will
|
||
|
|
download the packages' sources.
|
||
|
|
|
||
|
|
You may now build your rootfs with:
|
||
|
|
|
||
|
|
$ make
|
||
|
|
|
||
|
|
(This may take a while, consider getting yourself a coffee ;-) )
|
||
|
|
|
||
|
|
Result of the build
|
||
|
|
-------------------
|
||
|
|
|
||
|
|
After building, you should obtain this tree:
|
||
|
|
|
||
|
|
output/images/
|
||
|
|
+-- bcm2708-rpi-b.dtb [1]
|
||
|
|
+-- bcm2708-rpi-b-plus.dtb [1]
|
||
|
|
+-- bcm2709-rpi-2-b.dtb [1]
|
||
|
|
+-- bcm2710-rpi-3-b.dtb [1]
|
||
|
|
+-- bcm2710-rpi-3-b-plus.dtb [1]
|
||
|
|
+-- boot.vfat
|
||
|
|
+-- rootfs.ext4
|
||
|
|
+-- rpi-firmware/
|
||
|
|
| +-- bootcode.bin
|
||
|
|
| +-- cmdline.txt
|
||
|
|
| +-- config.txt
|
||
|
|
| +-- fixup.dat
|
||
|
|
| +-- start.elf
|
||
|
|
| `-- overlays/ [2]
|
||
|
|
+-- sdcard.img
|
||
|
|
`-- zImage
|
||
|
|
|
||
|
|
[1] Not all of them will be present, depending on the RaspberryPi
|
||
|
|
model you are using.
|
||
|
|
|
||
|
|
[2] Only for the Raspberry Pi 3 Model (overlay pi3-miniuart-bt is needed
|
||
|
|
to enable the RPi3 serial console otherwise occupied by the bluetooth
|
||
|
|
chip). Alternative would be to disable the serial console in cmdline.txt
|
||
|
|
and /etc/inittab.
|
||
|
|
|
||
|
|
How to write the SD card
|
||
|
|
========================
|
||
|
|
|
||
|
|
Once the build process is finished you will have an image called "sdcard.img"
|
||
|
|
in the output/images/ directory.
|
||
|
|
|
||
|
|
Copy the bootable "sdcard.img" onto an SD card with "dd":
|
||
|
|
|
||
|
|
$ sudo dd if=output/images/sdcard.img of=/dev/sdX
|
||
|
|
|
||
|
|
Insert the SDcard into your Raspberry Pi, and power it up. Your new system
|
||
|
|
should come up now and start two consoles: one on the serial port on
|
||
|
|
the P1 header, one on the HDMI output where you can login using a USB
|
||
|
|
keyboard.
|