2003-08-20 Chris Demetriou <cgd@broadcom.com>
* mips/crt0_cfe.S: New file. * mips/cfe_mem.c: New file. * mips/cfe_prestart.S: Remove. * mips/cfe.ld: Adjust to use crt0_cfe.o as the startup file, and and use _start as the entry point. Align BSS to 32-byte boundary. * mips/cfe.c: Reimplement to fit on top of a crt0_cfe.o file. * mips/cfe_api.h (__libcfe_stack_size, __libcfe_mem_limit) (__libcfe_meminit, __libcfe_stack_top): New prototypes. * mips/Makefile.in (CFEOBJS): Replace cfe_prestart.o with cfe_mem.o. (cfe.o, cfe_api.o, cfe_mem.o, crt0_cfe.o): New targets. * mips/configure.in: Build and install crt0_cfe.o when CFE support is built. * mips/configure: Regenerate.
This commit is contained in:
263
libgloss/mips/crt0_cfe.S
Normal file
263
libgloss/mips/crt0_cfe.S
Normal file
@@ -0,0 +1,263 @@
|
||||
/*
|
||||
* crt0_cfe.S -- Runtime startup for MIPS targets running CFE.
|
||||
*
|
||||
* Copyright 2003
|
||||
* Broadcom Corporation. All rights reserved.
|
||||
*
|
||||
* This software is furnished under license and may be used and copied only
|
||||
* in accordance with the following terms and conditions. Subject to these
|
||||
* conditions, you may download, copy, install, use, modify and distribute
|
||||
* modified or unmodified copies of this software in source and/or binary
|
||||
* form. No title or ownership is transferred hereby.
|
||||
*
|
||||
* 1) Any source code used, modified or distributed must reproduce and
|
||||
* retain this copyright notice and list of conditions as they appear in
|
||||
* the source file.
|
||||
*
|
||||
* 2) No right is granted to use any trade name, trademark, or logo of
|
||||
* Broadcom Corporation. The "Broadcom Corporation" name may not be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without the prior written permission of Broadcom Corporation.
|
||||
*
|
||||
* 3) THIS SOFTWARE IS PROVIDED "AS-IS" AND ANY EXPRESS OR IMPLIED
|
||||
* WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
|
||||
* NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM BE LIABLE
|
||||
* FOR ANY DAMAGES WHATSOEVER, AND IN PARTICULAR, BROADCOM SHALL NOT BE
|
||||
* LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
||||
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
||||
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
|
||||
* BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
|
||||
* WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
|
||||
* OR OTHERWISE), EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
*/
|
||||
|
||||
/*
|
||||
* Derived from crt0_cygmon.S:
|
||||
*
|
||||
* Copyright (c) 1995, 1996, 1997, 2000 Red Hat, Inc.
|
||||
*
|
||||
* The authors hereby grant permission to use, copy, modify, distribute,
|
||||
* and license this software and its documentation for any purpose, provided
|
||||
* that existing copyright notices are retained in all copies and that this
|
||||
* notice is included verbatim in any distributions. No written agreement,
|
||||
* license, or royalty fee is required for any of the authorized uses.
|
||||
* Modifications to this software may be copyrighted by their authors
|
||||
* and need not follow the licensing terms described here, provided that
|
||||
* the new terms are clearly indicated on the first page of each file where
|
||||
* they apply.
|
||||
*/
|
||||
|
||||
/*
|
||||
* This file does minimal runtime startup for code running under
|
||||
* CFE firmware.
|
||||
*
|
||||
* It does minimal hardware initialization. In particular
|
||||
* it sets Status:FR to match the requested floating point
|
||||
* mode.
|
||||
*
|
||||
* It is meant to be linked with the other files provided by libcfe.a,
|
||||
* and calls routines in those files.
|
||||
*/
|
||||
|
||||
#ifdef __mips16
|
||||
/* This file contains 32 bit assembly code. */
|
||||
.set nomips16
|
||||
#endif
|
||||
#ifdef __mips_embedded_pic
|
||||
# error -membedded-pic is not supported.
|
||||
#endif
|
||||
|
||||
#include "regs.S"
|
||||
|
||||
/*
|
||||
* Set up some room for a stack. We just grab a chunk of memory.
|
||||
*/
|
||||
#define STARTUP_STACK_SIZE (1 * 1024)
|
||||
|
||||
.comm _lstack, STARTUP_STACK_SIZE
|
||||
|
||||
.text
|
||||
.align 4
|
||||
|
||||
/*
|
||||
* Without the following nop, GDB thinks _start is a data variable.
|
||||
* This is probably a bug in GDB in handling a symbol that is at the
|
||||
* start of the .text section.
|
||||
*/
|
||||
nop
|
||||
|
||||
|
||||
/*
|
||||
* On entry, the following values have been passed in registers
|
||||
* by the firmware:
|
||||
*
|
||||
* a0: firmware handle
|
||||
* a1: zero (unused)
|
||||
* a2: firmware callback entrypoint
|
||||
* a3: CFE entrypoint seal (unused)
|
||||
*
|
||||
* They must be preserved until the CFE entrypoint and handle
|
||||
* are passed to __libcfe_init().
|
||||
*/
|
||||
|
||||
.globl _start
|
||||
.ent _start
|
||||
_start:
|
||||
.set noreorder
|
||||
/* Set the global data pointer, defined in the linker script. */
|
||||
la gp, _gp
|
||||
|
||||
#ifndef __mips_soft_float
|
||||
/* If compiled for hard float, set the FPU mode based on the
|
||||
compilation flags. Note that this assumes that enough code
|
||||
will run after the mtc0 to clear any hazards. */
|
||||
mfc0 t0, C0_SR
|
||||
or t0, t0, (SR_CU1 | SR_FR)
|
||||
#if (__mips_fpr == 32)
|
||||
xor t0, t0, SR_FR /* If 32-bit FP mode, clear FR. */
|
||||
#endif
|
||||
mtc0 t0, C0_SR
|
||||
#endif
|
||||
.end _start
|
||||
|
||||
/*
|
||||
* zero out the bss section.
|
||||
*/
|
||||
.globl _zerobss
|
||||
.ent _zerobss
|
||||
_zerobss:
|
||||
/* These variables are defined in the linker script. */
|
||||
la v0, _fbss
|
||||
la v1, _end
|
||||
|
||||
3:
|
||||
sw zero, 0(v0)
|
||||
bltu v0, v1, 3b
|
||||
addiu v0, v0, 4 /* Delay slot. */
|
||||
.end _zerobss
|
||||
|
||||
/*
|
||||
* Setup a small stack so we can run some C code, and do
|
||||
* the library initialization. (32 bytes are saved for
|
||||
* the argument registers' stack slots.)
|
||||
*/
|
||||
.globl _stackinit
|
||||
.ent _stackinit
|
||||
_stackinit:
|
||||
la t0, _lstack
|
||||
addiu sp, t0, (STARTUP_STACK_SIZE - 32)
|
||||
jal __libcfe_init
|
||||
nop
|
||||
|
||||
/*
|
||||
* Setup the stack pointer --
|
||||
* __libcfe_init() returns the value to be used as the top of
|
||||
* the program's stack.
|
||||
*
|
||||
* We subtract 32 bytes for the 4 argument registers, in case
|
||||
* main() wants to write them back to the stack. The caller
|
||||
* allocates stack space for parameters in the old MIPS ABIs.
|
||||
* We must do this even though we aren't passing arguments,
|
||||
* because main might be declared to have them.)
|
||||
*
|
||||
* We subtract 32 more bytes for the argv/envp setup for the
|
||||
* call to main().
|
||||
*/
|
||||
subu v0, v0, 64
|
||||
move sp, v0
|
||||
|
||||
.end _stackinit
|
||||
|
||||
/*
|
||||
* initialize target specific stuff. Only execute these
|
||||
* functions it they exist.
|
||||
*/
|
||||
.globl hardware_init_hook .text
|
||||
.globl software_init_hook .text
|
||||
.type _fini,@function
|
||||
.type _init,@function
|
||||
.globl atexit .text
|
||||
.globl exit .text
|
||||
.globl _crt0init
|
||||
.ent _crt0init
|
||||
_crt0init:
|
||||
la t9, hardware_init_hook # init the hardware if needed
|
||||
beq t9, zero, 6f
|
||||
nop
|
||||
jal t9
|
||||
nop
|
||||
6:
|
||||
la t9, software_init_hook # init the software if needed
|
||||
beq t9, zero, 7f
|
||||
nop
|
||||
jal t9
|
||||
nop
|
||||
7:
|
||||
la a0, _fini
|
||||
jal atexit
|
||||
nop
|
||||
|
||||
#ifdef GCRT0
|
||||
.globl _ftext
|
||||
.globl _extext
|
||||
la a0, _ftext
|
||||
la a1, _etext
|
||||
jal monstartup
|
||||
nop
|
||||
#endif
|
||||
|
||||
jal _init # run global constructors
|
||||
nop
|
||||
|
||||
addiu a1,sp,32 # argv = sp + 32
|
||||
addiu a2,sp,40 # envp = sp + 40
|
||||
#if __mips64
|
||||
sd zero,(a1) # argv[argc] = 0
|
||||
sd zero,(a2) # envp[0] = 0
|
||||
#else
|
||||
sw zero,(a1)
|
||||
sw zero,(a2)
|
||||
#endif
|
||||
|
||||
jal main # call the program start function
|
||||
move a0,zero # set argc to 0; delay slot.
|
||||
|
||||
# fall through to the "exit" routine
|
||||
jal exit # call libc exit to run the G++
|
||||
# destructors
|
||||
move a0, v0 # pass through the exit code
|
||||
.end _crt0init
|
||||
|
||||
/*
|
||||
* _exit -- Exit from the application. This is provided in this file because
|
||||
* program exit should shut down profiling (if GCRT0 is defined),
|
||||
* and only this file is compiled with GCRT0 defined.
|
||||
*/
|
||||
.globl _exit
|
||||
.ent _exit
|
||||
_exit:
|
||||
7:
|
||||
move s0, a0 /* Save in case we loop. */
|
||||
|
||||
#ifdef GCRT0
|
||||
jal _mcleanup
|
||||
nop
|
||||
#endif
|
||||
|
||||
la t0, hardware_exit_hook
|
||||
beq t0,zero,1f
|
||||
nop
|
||||
jal t0
|
||||
nop
|
||||
|
||||
1:
|
||||
/* Call into the library to do the heavy lifting. */
|
||||
jal __libcfe_exit
|
||||
move a0, s0 /* Delay slot. */
|
||||
|
||||
b 7b /* Loop back just in case. */
|
||||
nop
|
||||
.end _exit
|
||||
|
||||
/* EOF crt0_cfe.S */
|
Reference in New Issue
Block a user